Re: Installation of 4.60 fails in german version of 2008R2x64
Hi, I have the same problem but with English 2008 R2. I have tried and windows 7 but with no luck (same issues).Does anybody know the resolution for this problem? Kind regards, Milan
View ArticleClik here to view.
Re: LEDs of switch and adapters not lighting up.
Hi Eddie, I tried setting up the link with the command you mentioned above. Still, port status is PORT_DOWN.
View ArticleRe: LEDs of switch and adapters not lighting up.
Hi Komal, What is the switch software you are using?run "show version concise"what are the cable types and models?run (from enable mode) "show interfaces ethernet transceiver"
View ArticleRe: LEDs of switch and adapters not lighting up.
Hi Eddie, Thanks for looking into it. I am using Fibre Optic Cable(speed upto 56GbE). I could see LED lightened in one port after I reconnected cables, but the other port(enp26s0d1) is still facing the...
View Articlemlx5_core - device's health compromised
Dear all, I have a connect-IB adapter, firmware version 10.10.5020, connected via a PCIe switch to a host running CENTOS 7 and Mellanox drivers MLNX_OFED_LINUX-2.4-1.0.4-rhel7.0-x86_64.Just after boot,...
View ArticleClik here to view.
Re: LEDs of switch and adapters not lighting up.
Issue resolved. My physical port of the adapter was damaged.
View ArticleRe: mlx5_core - device's health compromised
Hello, Can you pass on the full dmesg output from this event ? Also, can you run the mget_temp tool and let us know how much you're seeing ? The syntax should be something like :#mst start# mget_temp...
View ArticleRe: mlx5_core - device's health compromised
Dear Erez, thank you for your reply.Attached you can find the full dmesg output of the event. The temperature read by your suggested command is 51°C: #mget_temp -d /dev/mst/mt4113_pciconf0>51 Where...
View ArticleRe: Reserved op code 0x80 during UC transfers
I think the packets were are detecting may be Backward Explicit Congestion Notification (BECN) packets used for congestion control for UC transfers. These Congestion Notification Packets (CNP) are...
View ArticleNew Cisco ASA 5506-X will replace ASA 5505
Cisco ASA 5506-X ASA5506-K9 firewall is supposed to have the FirePOWER engine and also equipped with Gigabit ports. The FirePOWER module (most probably will be a software module on the low-end modules)...
View ArticleRe: mlx5_core - device's health compromised
Temperature sensor in Connect-IB card (diodes) are located and spread inside the the adapter silicon,and I guess you're in the safe zone as the threshold should be 100 [degrees centigrade]. The...
View ArticleClik here to view.
Re: Reserved op code 0x80 during UC transfers
I can say that I've never seen medium or big sized Infiniband clusters using CC as of today.
View Article2.0.0-9 ibdump does not work with firmware version 2.7.000
Hi, I am new to this forum. :-) We tried to run ibdump to look for multicast traffic.The 2.0.0-9 ibdump barfs on device FW version: -E- Device firmware version (2.7.000) does not support ethernet...
View ArticleClik here to view.
Re: 2.0.0-9 ibdump does not work with firmware version 2.7.000
Ah, I interpreted the error message incorrectly. The "2.11.1140" is actually meant the version of firmware, not the version of ibdump. That makes sense now. Sorry for the noise. Not a good way to join...
View ArticleWhat software to download?
I have some old Mellanox hardware and I am trying to move it from Red Hat 5 to RHEL 6. I download the most current software and tried to install it, but the install froze. How do I determine what...
View ArticleRe: What software to download?
To give everyone a little more background on my problem, we are running ROCKS 5.4 on RHEL 5. The system can be patched to pass security, but it is one of the last remaining RHEL 5 machines. I am trying...
View ArticleRe: What software to download?
Hello, Mellanox OFED drivers can be downloaded from this link : Mellanox Products: Mellanox OpenFabrics Enterprise Distribution for Linux (MLNX_OFED) What Infiniband card do you have ?
View ArticleClik here to view.
Re: 2.0.0-9 ibdump does not work with firmware version 2.7.000
What HCA are we talking about ? mst startflint -d /dev/mst/mt***pciconf0 q
View ArticleRe: What software to download?
Here is the revevant portion of the output of lspci. Since this is running on an early version of Red Hat Enterprise Linux 5, I may have to go back and get an archive version of the software, but I...
View ArticleClik here to view.
Re: What software to download?
I downloaded the latest software, untarred it, and started the installed. The install proceeded until it got to the firmware upgrade. It failed on that. Then I tried to run /etc/init.d/openibd. It...
View Article