Re: ISR9024D-M
I noticed in the directions for cabling it says this: To connect multi-purpose cable of an ISR 9024-M (internally managedunit):Step 1 Connect the DB-9 connector and the RJ45 connector to each extremity...
View ArticleRe: Voltaire ISR-9024D (NOT -M) Question
No worries. We're not super pedantic about it, it's just a good guideline to follow. Thanks for moving this to it's own thread.
View ArticleRe: Re: ISR9024D-M
Hmmm, the instructions with that "multi-purpose" cable sound fairly complicated. For my 9024D-M, I just plugged a standard everyday cat 5e ethernet cable into the front ethernet port (next to "I2C" DB9...
View ArticleRe: Re: ISR9024D-M
im going to have to try putting it on its own switch to eliminate complications. I tried the command above but it tells me: route_dst_netlink: can't find interface "vmbr0" This is on a proxmox lunix...
View ArticleRe: Re: ISR9024D-M
Wireshark shows me this everytime with the ISR directly connected to my second ether port on my desktop: 24250.097091000Heurikon_69:a1:a0BroadcastARP60Gratuitous ARP for 192.168.2.9...
View ArticleClik here to view.
Re: Re: Re: ISR9024D-M
Interesting, so it sounds like it's trying to use 192.168.2.9. "Heurikon" is most likely correct too, as that's how the board shows up in nmap as well: Re: Voltaire ISR-9024D (NOT -M) Question Are you...
View ArticleRe: UFM 4.0 server connection error - server not responding
That is correct! just set an IP address to your ib0 interface and that should do it!setting up the IP for the IB interface is the same as you would do for your Eth interface.
View ArticleRe: Re: Re: ISR9024D-M
I have put the ether on the same subnet as the switch (192.168.2.8) but i cannot ping the ISR. when i connect the ISR to a trendnet TEG-S80g 1GB switch it doesnt seem to establish a connection (both...
View ArticleRe: UFM 4.0 server connection error - server not responding
Hello. Yes, I have a license and I started ufmd with no errors. In /var/log/messages, I see the following: ufm: ufmd monitorufm: Running UFM in monitoring modeufm: Starting ibsim with options: -P...
View ArticleRe: UFM 4.0 server connection error - server not responding
Yes, part of my response was cut off, apparently because I had someunderline characters. Here is the rest of the log contents. Under ufm.log in /opt/ufm/files/log/, there is the following: UFM daemon...
View ArticleRe: Re: Re: ISR9024D-M
Interesting. It's obviously wanting to use the 192.168.2.9 address, but doesn't seem to be actually going ahead and using it. Unfortunately it's been ages since I had to work with IP(v4) network...
View ArticleClik here to view.
Re: Re: ConnectX-3 not going up in Centos 6.4 (and SL6.4)
Just remembered... with flint you can query a card to extract the .ini file settings it already has: $ flint -d [PCI_bus_address_of_card] dc > somefile.ini For example, with an older card in a test...
View Articlevoltaire 4036 cant connect to CLI
I am unable to connect to my switch at all via putty or hyperterminal. I have tried all different connections. Any other ideas?
View ArticleRe: voltaire 4036 cant connect to CLI
Jae-Hoon Choi - Any ideas? Justin Krause - If no-one here is able to get you up and running, there are several helpful people in the Serve The Home networking forum with Voltaire 4036 switches who may...
View ArticleRe: Re: Re: ISR9024D-M
I set one interface on my pc to 192.168.2.9 and wireshark shows that it detected a duplicate ip. But no request from the ISR to fall back to another address.... Do the infiniband interfaces have a...
View ArticleRe: Re: Re: Re: ISR9024D-M
I'm not 100% sure. I've only used the default IP with my ISR 9024D-M, without never really needing to think outside of this particular box. Out of curiosity, have you looked all through the...
View ArticleOld device type when updating flash
According to the latest (April 2013) version of the MFT user manual, mlxburn should support device type 25204 (Infinihost III LX). However, when I try to update the firmware, I receive an error that it...
View ArticleRe: Re: Re: Mellanox (old Voltaire) ISR9024D-M recover flash area
Jae-Hoon Choi - Discovered something interesting. I can log into my 9024D-M as root (not "admin") using telnet/ssh. Default password is "123456", same as for the admin user. It gives shell access...
View ArticleRe: Re: Re: ISR9024D-M
Just found something out by accident. I've logged into my 9024D-M switch as root, and ifconfig is showing the default IP address of the ipoib0 interface as "192.168.2.100". If you configure one of...
View ArticleRe: voltaire 4036 cant connect to CLI
You must connect via serial console cable.Then select management interface to ethernet via some CLI command.default ip address configuration for management ethernet is DHCP. Try check dhcp lease lists...
View Article
