Clik here to view.
Is it possible to switch ConnectX-3 VPI into Ethernet mode in Solaris 11.1?
Is see there are guides on how to do this in Windows and Linux but nothing for Solaris 11.1. Is it possible/supported?
View ArticleClik here to view.
IPoIB not working with MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR / 10GigE]
Good afternoon,I am trying to use IPoIB with an infiniband card MT26428. The Idea is to use a small cluster with MPI support over InfiniBand, using the SLURM scheduler. I was using SGE as scheduler and...
View ArticleWhere is driver for Oracle Ent Linux 5 update 9?
Is there a compatible version for OEL 5U9 ?
View ArticleRe: IPoIB not working with MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR /...
Hi!You were configure C class subnet.But your IP address not in same subnet range.* 10.0.1.xxx vs 10.0.2.xxxAnd...1st interface is eth0, but 2nd interface is Ib0.(Does it Ethernet mode and IPoIB...
View ArticleRe: ESXi 5.5 ib_ipoib questions
Hi!I think that's derive from Mellanox's marketing policy and Intel's SR-IOV support and VMware ESXi's limitation.VMware moved from ESX to ESXi - That's a only distros. That's a good choice for reduce...
View ArticleRe: Please let me know 40Gb Ethernet card can split to 4 x 10Gb ?
Hi Ophir, I had inquired previously about such functionality for ESXi 5 and referenced this Mellanox link - http://ir.mellanox.com/releasedetail.cfm?ReleaseID=601497 There are also other documents...
View ArticleClik here to view.
Re: IPoIB not working with MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR /...
Hi, thanks for your anser,It appear strange to me, because with usual ethernet IPv4 you can have 2 different interfaces with separated networks (that's what I'm already doing for ethernet network on...
View Articlesetup MaxReadReq to 4096 bytes definitely
Hello,when installing the Mellanox drivers for infiniband, the installer complains that the MaxReadReq of my PCI card is too low, and that I need to set it to 4096. In the current session I do :#...
View ArticleClik here to view.
sRB-20210G factory default state and documentation?
Hello everyone, I recently got my hands on a pair of Voltaire sRB-20210G from ebay and tried to configure them. In the process of doing so, I did a factory reset to get rid of any configurations that...
View ArticleRe: Please let me know 40Gb Ethernet card can split to 4 x 10Gb ?
Hi Matt, I'm not sure I understand what you wish to get from ESXi5? Thanks,Ophir.
View ArticleRe: IPoIB not working with MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR /...
Hi! I thought you're in the vSphere ESXi environment... If you are working Linux enviroment use the eIPoIB protocol. IPoIB support IP application but there is some limitation. But new eIPoIB protocol...
View ArticleClik here to view.
Re: Where is driver for Oracle Ent Linux 5 update 9?
You can try RHEL 5.9 version: http://www.mellanox.com/downloads/ofed/MLNX_OFED-1.5.3-4.0.42/MLNX_OFED_LINUX-1.5.3-4.0.42-rhel5.9-x86_64.isoIf you are using different kernel - try to run...
View ArticleRe: Oracle enterprise linux 6.5 driver problem
2.1-1.0.6 now available with OEL 6.5 support:http://www.mellanox.com/downloads/ofed/MLNX_OFED-2.1-1.0.6/MLNX_OFED_LINUX-2.1-1.0.6-oel6.5-x86_64.iso
View ArticleHow to clear the target connection via add_target
Hello experts,I missed to create the target connection via add_target. as follows. (ex.)# echo...
View ArticleClik here to view.
Re: Need help installing OFED 2.1 on Centos 6.5
Hi there, Did you up the maxReadReq size too?
View ArticleClik here to view.
Configuration settings for IPoIB performance
Hello, I'm seeing very poor IPoIB performance with QDR switch, RH 6.5, when measured with iPerf.[ 3] 0.0-10.0 sec 3.31 GBytes 2.84 Gbits/sec I implemented the changes recommended in performance...
View ArticleRe: Configuration settings for IPoIB performance
10Gb is normal. All QDR interface use the QUAD CHANNEL.Therefore 10x4 equal to 40Gb. If you want to configure MTU=65520, you must enable the CM mode.I'm not a Linux admin but virtualization one. You...
View ArticleRe: Configuration settings for IPoIB performance
Pure centos 6.5 x86_64 1. echo "connected" > /sys/class/net/ib0/mode2. ifconfig ib0 mtu 65520 No other tuning! No external OFED install! service rdma start iperf -P 1 -c...
View ArticleSys log message
Hi , anyone know what these messages mean, anything to worry about and if not, how can I stop them from filling up my syslog files? Apr 25 16:12:29 hksw1001 issd[4840]: TID 1299130464: [issd.ERR]:...
View ArticleMXM ERROR failed to create send cq: Cannot allocate memory
I am trying to setup a small HPC cluster using Mellanox MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR / 10GigE] cards and a M3601Q switch to work with openMPI and SLURM. I have read that I need to...
View Article