Clik here to view.
Re: Not able to build lustre 2.5.0 against OFED 2.2.
Below patch solved the problem.http://review.whamcloud.com/#/c/8451/1 Thanks,Aayush.
View ArticleI can't find the firmware of the PSID SM_2091000001000 on your website
I can't find the firmware of the PSID SM_2091000001000 on your website. The infomation of the device is listed as below:02:00.0 InfiniBand: Mellanox Technologies MT26428 [ConnectX VPI PCIe 2.0 5GT/s -...
View ArticleClik here to view.
Re: I can't find the firmware of the PSID SM_2091000001000 on your website
Hi Ning Li, The PSID indicates that it's an on-board SuperMIcro HCA, you should contact SuperMicro to get the latest Firmware for that LOM device. Please provide them the PSID and the server model
View ArticleClik here to view.
Re: I can't find the firmware of the PSID SM_2091000001000 on your website
Thanks for your reply! I'll contact SuperMicro.
View ArticleClik here to view.
Re: Not able to build lustre 2.5.0 against OFED 2.2.
Original threadhttps://lists.01.org/pipermail/hpdd-discuss/2014-September/001268.html
View ArticleClik here to view.
get_pcounter and collectl
Hello All, I'm attempting to set up a full implementation of collectl and it specifies in the conf file that the command 'get_pcounter' which is supposedly provided by the Mellanox OFED install. Has...
View Articlewhich VMA card to buy to connect HP DL360p Gen8 to 1000Base-T
I'm using HP DL360p Gen8I need to connect it to 1 Gb cooper Ethernet (1000BASE-T)I want to use VMA to improve latency.What is the best card for me (and compatible transceivers)?
View ArticleRe: Re: "Missing UAR" kernel error on boot, ConnectX-3 not detected by the OS
i am having this problem too. this is the message from my syslog:Oct 2 05:59:56 fr-dev11 kernel: [ 670.201294] mlx4_core: Mellanox ConnectX core driver v1.1 (Oct 2 2014)Oct 2 05:59:56 fr-dev11...
View ArticleRe: Re: Re: "Missing UAR" kernel error on boot, ConnectX-3 not detected by...
at bit more information gleaned using flint: Image type: FS2FW Version: 2.32.5100FW Release Date: 3.9.2014MIC Version: 1.5.0Config Sectors: 2Product Version: 02.32.51.00Rom Info:...
View ArticleRe: which VMA card to buy to connect HP DL360p Gen8 to 1000Base-T
VMA was tested on high speed networks 40/56Gbit/s, in your case your are running 1Gb, that is much slower and probably this will be a bottleneck.VMA should run well on any CX3 VPI or Ethernet HCAs...
View ArticleRe: how spread my net bandwidth when I used Send / receive or read / write...
I would like to suggest to start with latest software/firmware and follow instructions in Mellanox Tuning Guide Mellanox Products: Mellanox OpenFabrics Enterprise Distribution for Linux...
View ArticleClik here to view.
Troubleshooting Mellanox InfiniBand card
We have a Mellanox MT27500 Family, ConnectX-3 FDR InfiniBand card that we have purchased and set up in our Mechanical Engineering department cluster. Everything was working fine until a week ago when...
View ArticleClik here to view.
Re: How to stack two Voltaire 4036
Hi andre, sorry it took me so long time to reply, the email ended up in spam box and I have just seen it. I will do the tests you recommended see what happen. Thank you very much again for all your help
View ArticleRe: How to stack two Voltaire 4036
Hi!If you test on Windows Platform, you must use SMB Direct with firmware 2.10.720. QDR's throughput is real 32Gb.But you can use that performance on SRP, MPI, SMB Direct only. QDR HCA's performance is...
View ArticleClik here to view.
Problems installing WinOF on Windows 8.1
I'm trying to install WinOF for windows 8.1 (which is currently installed on the computer), but when I try to install it I get "MLNX_VPI requires that your computer is running Windows 8.1" Does anyone...
View ArticleMTU 4K on ISR 9024-D-M
Hello, I want to use MTU 4K on my connections. Where and how can I setup the MTU on the switch?Neither in GridManager nor in CLI I can find something to do it... With best regardseffe
View ArticleClik here to view.
Re: get_pcounter and collectl
Hi Jared, This utility is no longer maintained thus was dropped. you have a new set of IB tools coming with ibutils2 package which can show you relevant information.
View ArticleMTO/MPO Cable Question
I have a pair of Mellanox switches, a MIS5030Q-1SFC and a MIS5022Q that I am looking to connect together using a pair of MFM4R12C-QDR transceivers, due to the distance involved. I had had this working...
View Article